Honey Comp 
Carl started years back with the Compressor Limiter…that big black hand-made-in-Denmark 
compressor that brought studio comps to the pedal board.  The word got out that it was 
just too big for modern pedal boards, so Carl redesigned that pedal into a much smaller 
format, preset (or fixed) the Threshold and Response leaving just two knobs for Comp and 
Level. The feedback we got was overwhelming…players were telling us the Comp Limiter had 
the same sonic clarity, the same headroom and the same quietness that the big studio comps 
had but was so quick and easy to use.  Carl could have left it there, but that’s not Carl!

Welcome the Honey Comp, and it’s as sweet as …. well, you know …. honey.  This pedal is the 
same as the Comp Limiter in every way … same Gray anodized finish, same footprint and the same 
simplicity of use with one compression control and one level control. It is pretty much the perfect 
compressor, so what could Carl possible upgrade? Easy!  Carl added a Dry volume which allows you 
parallel processing with three knobs!  Parallel Processing is a studio technique which takes a 
heavily compressed signal (which through compression loses some dynamics if not all) and allows 
you to add a clean (Dry) signal on top replacing those dynamics giving your guitar three-dimensionality 
and allowing the guitar to cut through the mix.  For those of you used to studio work, this is a very 
well-known technique, but usually too complex for a pedal board! The three knobs allow you to balance 
the Compressed signal with the Dry signal quickly and efficiently for a very pro sound!

The Carl Martin Honey Comp incorporates the special CM developed DC/DC converter circuitry. 
This enables us to run the pedal with +-12V internally, which is necessary, in order to maintain 
the same sonic quality and headroom as on the “old” Compressor/Limiter, using a regular 9V DC 200mA 
external power supply.

Specifications
Input: 1M Ohm
Output: 200 Ohm
S/N Ratio: 105 dB (clean out)
THD distortion: 0,05%
Compression Range: from 1:1 to 1:00
Dimensions : 60 (W) x 115 (D) x 50 (H) mm
Weight: 340g

Soundking Amp AQ2350 2*350W 8 OHM

Features
-high efficiency, energy saving  
-active PFC, power factor 0.99
-high output to drive 2 Ohm load stably  
-compact but solid structure  
-perfect protection  
-meet the requirement of production compliance and electromagnet compatibility.
-Variable speed fan for cooling.

Function
-stereo/mono/bridge operation modes  
-sensitivity 1Vrms,gain 32dB, 26dB for option
-XLR input connector 
-professional speaker connector 
-output over load/short circuit protection  
-DC output protection 
-70? power compression 
-thermal protection 
-Thermal indication

Rated power(EIAJ THD=1%,1kHz,2 CH working simultaneously): 
8O/ stereo: 2×350W 
4O/ stereo: 2×595W 
2O/ stereo: 2×1015W 
16O/ bridged: 700W 
8O/ bridged: 1190W 
4O/ bridged: 2030W 

RMS output voltage(THD=1%,1kHz): 52.9V  
Voltage gain: 34.5 dB 
(1kHz, bypass LPF): 50V/us 
Input sensitivity( rated output power ,1kHz): 1Vrms 
THD+N (10%  rated output power,):0.02%  
IMD-SMPTE(10%  rated output power,): 0.05% 
DIM30(10%  rated output power,): 0.05% 
Crosstalk rejection(less than rated power, 20 Hz -1 kHz): =80 dB 
Frequency response(10%  rated output power,8O,20Hz - 20 kHz): ±0.2dB 
Input impedance: 20kO(bal) ,10kO(unbal) 
Damping factor(8O,20 Hz -100 Hz): =300 
S/N ratio (A weighted,20Hz-20kHz): =105dB 
Power supply: 90-260VAC, 50/60 Hz 
protection: over load/thermal/DC output protection 
dimension(W×H×D): 483×44×323mm 
Net weight: 5.0kg